Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
We have noticed this article relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the internet and thought it made sense to talk about it with you in this article.
Setting up a bath tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is readily easily accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old tub and also place the new tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and set in the brand-new one. Make certain you have certified on your own for the job and fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is better to think about employing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your bathroom if you have actually currently acquired a brand-new tub as well as do not need to change the plan of your previous water system pipes.
Your tools and also product checklist must consist of the following:
Planning for the Installment
First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite troublesome due to the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bathtub till the level reviews level.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the supply of water and also check all joints and brand-new pipework for leakages and also tighten them if essential. Fill the bath tub and also inspect the overflow electrical outlet and also the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub should wait up until the bathtub has been utilized at least when as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in complications with dampness and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very excited about A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed reading my page. Are you aware of anybody else who is occupied with the topic? Be sure share it. Many thanks for your time. Visit again soon.
Plumbing challenges? Get immediate solutions. Report this page